CAT Full catalog

Commercial Fleet Repair Services for Santa Ana

Name: Fleet Services OCRV
Address: 23281 E La Palma Ave, Yorba Linda, CA, 92887, US
Telephone: (714) 909-1844
Price range: $$

Fleet Services OCRV performs body, paint, structural and equipment install work on commercial fleet units at a single Yorba Linda facility. Scope covers collision and frame work, refinishing, graphics, box and trailer bodies, upfit equipment and glass. Engine, drivetrain and inspection certification work is handled elsewhere.

Categories: 8
Detailed services: 53
Catalog items: 530

WO-00 Posted rates

Our labor rates, published

No other commercial fleet shop in this market publishes a rate. Budget against ours before you ever pick up the phone.

Body and paint

$210 per hour

Panel work, structural straightening, refinish, and blend time.

Electrical and accessory

$260 per hour

Lighting circuits, liftgate power, camera and upfit wiring.

Diagnostic, scan and calibration

$285 per hour

One hour minimum, credited against an authorized repair.

Detail

$95 per hour

Prep, cut and buff, delivery detail.

Materials are calculated automatically on every written estimate: paint supplies at $55 per paint hour, body supplies at $5 per body hour, and $45 flat for hazmat handling where chemicals or refrigerant are involved. Sales tax of 7.75 percent applies to parts and materials. Labor is not taxed. See the full rate card.

IDX Category index

Eight categories, every one priced

WO-01

Collision and Structural

Frame, subframe, cab and panel repair for Santa Ana fleets, measured against factory datum and documented for the carrier.

9 detailed services

WO-02

Paint and Refinishing

Color matched refinishing for commercial fleets in Santa Ana, from single panel blends to full unit resprays and clear coat restoration.

6 detailed services

WO-03

Graphics and Wraps

Cast vinyl wraps, decals, reflective marking, unit numbering, and window film applied and removed in shop for Santa Ana fleets.

5 detailed services

WO-04

Box and Cargo Body

Skin, post, roof, door and liner repair on box and cargo bodies for Santa Ana fleets, with the cargo opening squared before release.

5 detailed services

WO-05

Trailer and Chassis

Skin and post repair, floor and crossmember work, landing gear, lamp circuits, tie down systems and coatings for Santa Ana trailer fleets.

6 detailed services

WO-06

Equipment and Upfit

Liftgates, service bodies, shelving, bulkheads, racks, hitches and work lighting installed and mounted to structure for Santa Ana fleets.

9 detailed services

WO-07

Glass and Accessories

Windshield replacement, chip resin repair, mirror and camera systems, step and running board mounting, plus flare and mud flap fitting.

5 detailed services

WO-08

Makes We Service

Body, paint, and structural repair organized by chassis platform, because an aluminum Class 8 cab and a unibody cargo van are different disciplines.

8 detailed services

SLA Schedule

How long a unit is off the road

Uptime is the number fleets actually buy. These are the bands we schedule against, by damage type rather than by vague promise.

Turnaround bands by damage tier
Tier	Typical scope	Time in shop
Light cosmetic	Single panel, bumper, mirror, decal set	1 to 3 business days
Moderate body	Multi panel, cargo door, box skin section	4 to 8 business days
Structural	Frame, subframe, cab mount, sectioning	2 to 4 weeks
Full refinish	Complete unit repaint or refleet	2 to 5 weeks
Upfit install	Liftgate, service body, shelving package	3 to 10 business days

ALL Complete list

The complete service catalog

Everything performed in house, grouped by category. Items with a dedicated page are linked. The rest are performed as part of a larger scope and are listed here so nothing is hidden.

WO-01 Collision and Structural

9 detailed, 64 additional

Fleet Collision Repair$1,500 up
Frame and Rail Straightening$2,200 up
Chassis and Subframe Repair$1,200 up
Panel Replacement and Sectioning$750 up
Cab and Door Repair$750 up
Dent and Paintless Dent Repair$400 up
Rust Repair and Undercoating$400 up
Structural Welding and Fabrication$750 up
ADAS Scan and Recalibration$285 up

Front bumper and impact bar replacement on cab chassis and box units
Grille, header panel and lamp bezel replacement after a frontal hit
Hood hinge, latch and gas strut replacement
Steel, aluminum and FRP fender replacement
Cab corner and rocker panel sectioning
Door skin replacement over an undamaged door frame
Door hinge pin and bushing replacement to correct sag
Door striker and latch realignment after body movement
Weatherseal replacement to cure wind noise and water intrusion
Cab mount bushing and isolator replacement
Cab mount bracket straightening and reinforcement
Frame rail measurement against manufacturer datum points
Frame rail sectioning at approved splice locations
Crossmember replacement and gusset fabrication
Rivet removal and replacement on riveted frame assemblies
Huck bolt and structural fastener replacement
Bumper mount and tow eye reinforcement
Entry step and step box frame repair
Roof panel repair after a low clearance strike
Roof bow and front header replacement
A pillar and B pillar repair on cutaway cabs
Windshield frame and pinchweld repair before glass is set
Two part structural adhesive panel bonding
Squeeze type resistance spot welding at approved joints
MIG plug and stitch welding on mild steel panels
MIG brazing on high strength steel where the procedure calls for it
Aluminum MIG and pulse welding on aluminum body structure
Self piercing rivet and rivet bonded panel attachment
Weld through primer application at mating flanges
Cavity wax injection inside boxed rails and pillars
Seam sealer replacement matched to the factory bead profile
Sound deadener and body pad replacement after panel work
Rust cut out and patch panel fabrication at cab seams
Localized media blasting of corrosion before repair
Epoxy primer and sealer application on bare metal
Chassis and undercarriage corrosion coating after structural work
Paintless dent removal on steel and aluminum skins
Crease and edge dent repair using glue pull tabs
Stud welding and slide hammer pulling on heavy gauge panels
Sheet metal shrinking and stress relief after a pull
Body filler and polyester glaze work to restore panel contour
Panel gap setting and flush fit verification
Mirror arm and mounting bracket replacement after a side strike
Grab handle and mirror mount reinforcement
Fuel fill door and surround panel repair
Battery box and toolbox mount bracket repair
Air dam, chin spoiler and side skirt replacement
Aerodynamic fairing repair and remount
Mud flap hanger and bracket replacement
Rear frame extension and bumper crossmember replacement
Rear impact guard replacement with weld verification
Pre repair and post repair network health scans
Forward camera static recalibration after windshield or bracket work
Radar bracket alignment and target based recalibration
Blind spot sensor bracket replacement on box and van bodies
Backup camera and harness rerouting after rear damage
Marker and clearance lamp circuit repair on damaged panels
Harness section repair where a panel was cut for access
Structural measurement reports prepared for the claim file
Teardown blueprinting and supplement documentation
Bench anchoring and pulling with universal and dedicated clamps
Three dimensional measurement during and after the pull
Test fit of doors, hood and cargo openings before refinish
Final quality control inspection and release checklist

WO-02 Paint and Refinishing

6 detailed, 50 additional

Single panel refinish on doors, fenders, and quarter panels
Bumper and fascia refinish, including textured black restoration
Mirror housing and mirror arm refinish
Grille surround and grille shell refinish
Hood refinish and hood leading edge sealing
Roof and box top refinish
Door jamb, hinge pillar, and striker area refinish
Roll up door slat refinish
Swing door inner face refinish on cargo bodies
Rocker panel and step well refinish
Wheel arch and fender flare refinish
Fuel tank strap and bracket coating
Steel and alloy wheel refinish in fleet color
Ladder rack and roof rack refinish
Headache rack and cab guard refinish
Toolbox and compartment door refinish on service bodies
Liftgate platform and frame coating
Bulkhead and partition panel refinish
Frame rail and crossmember chassis coating
Underbody seam sealing prior to coating
Bare metal etch and epoxy priming
Urethane surfacer application and block sanding
Plastic substrate preparation with adhesion promoter
Fiberglass panel preparation and gel coat repair
Aluminum panel preparation and self etching primer
Galvanized and pre coated steel preparation
Spectrophotometer color read and formula mixing
Variant deck comparison and letdown card spray out
Tri stage and pearl mid coat matching
Single stage refinish on utility and chassis surfaces
Base coat and clear coat refinish on visibility panels
Two component urethane clear application and bake cycle
Film thickness measurement and panel by panel reporting
Dirt nib removal, cut, and buff
Machine compounding and refining polish
Clay bar and chemical iron decontamination
Paint sealant application after correction
Ceramic coating application on roofs, hoods, and box tops
Overspray removal from adjacent panels and glass
Water spot etching removal
Graffiti and tag removal from body sides
Anti graffiti clear application on high exposure panels
Protective coating on interior cargo walls
Non skid coating on steps, decks, and platforms
Stencil and template masking for two tone schemes
Two tone and accent stripe layout and spray
Reflective paint accent application on service bodies
Touch up kit preparation using the matched fleet formula
Panel edge sealing before reassembly
Fastener and seal replacement at reassembly

WO-03 Graphics and Wraps

5 detailed, 50 additional

Full coverage vinyl wrap on cargo vans and box bodies
Partial coverage wrap on lower panels and rear doors
Color change wrap including jambs and door returns
Printed graphics panels with ultraviolet overlaminate
Cut vinyl logo and wordmark application
Door logo sets in fleet standard placement
Rear door graphics and load door artwork
Hood and bumper accent graphics
Roof graphics for overhead and yard camera identification
Trailer side graphics on corrugated and smooth skins
Refrigerated body graphics in temperature rated film
Bus and shuttle body graphics and route panels
Perforated window graphics on rear and side glass
One way vision film with printed exterior graphic
Frosted and etched effect privacy film
Magnetic panel production for temporary branding
Removable film for seasonal or campaign graphics
Wrap seam repair and panel section replacement
Rivet and corrugation post heating
Edge sealer application at cut edges and rivet lines
Bubble, tent, and lift repair on existing wraps
Wrap removal with heat and controlled angle lifting
Adhesive residue removal and panel cleaning
Ghosting assessment and correction after removal
Machine polishing of ultraviolet shadow at decal boundaries
Lease return graphics strip with condition documented
Resale and auction preparation graphics removal
Fleet unit number cutting and application
Company name, city, and contact text application
Carrier identification number application per supplied marking list
Capacity, weight, and body specification text
Reflective unit numbers for night yard identification
Retroreflective conspicuity sheeting on side rails
Rear conspicuity strip and upper corner mark application
Failed and delaminated reflective tape removal
Reflective segment replacement after panel repair
Reflective chevron panel application on rear doors
Emergency service reflective striping and identification packages
Placard holder and sign bracket mounting
Hazard and equipment labels applied from supplied specification
Ceramic window film on cab and door glass
Metallized and dyed window film options per glass position
Security gauge film on cargo and side glass
Old window film removal and adhesive cleanup
Windshield top band film application
Template development for each body type in a fleet
Artwork proofing and print profile management
Color proofing across print runs for fleet consistency
Graphics files and marking lists held on account for repeat units
Batch scheduling for multi unit graphics programs

WO-04 Box and Cargo Body

5 detailed, 62 additional

Aluminum and FRP side skin panel replacement
Skin section splicing at a vertical post line
Front and rear corner post replacement
Rear frame and door jamb rebuild after a dock strike
Top rail and side rail extrusion replacement
Bottom rail and threshold repair on aluminum bodies
Roof bow replacement and roof sheet reskin
Translucent roof panel replacement for interior cargo light
Front header and nose panel replacement
Rivet removal and replacement in matching diameter and grip length
Structural adhesive rebonding of delaminated skin panels
Seam and rivet head sealing to stop water intrusion
Water leak testing of a repaired body before release
Interior scuff liner and plywood lining replacement
Logistics track and E track installation on cargo walls
Load bar and cargo rail repair
Interior bulkhead and partition repair
Roll up door panel and slat replacement
Roll up door track straightening and replacement
Roller, hinge and end cap replacement on roll up doors
Counterbalance spring tension adjustment and replacement
Cable, drum and pulley replacement on roll up assemblies
Roll up door bottom panel and weather strip replacement
Swing door hinge and cam bar replacement
Swing door lock rod, keeper and latch repair
Door gasket and header seal replacement
Reefer skin repair over foam core wall panels
Foam core delamination assessment and rebonding
Insulated panel section replacement
Insulated body interior liner and drain repair
Air chute and duct replacement inside insulated bodies
Insulated door gasket and threshold replacement
Hardwood cargo floor board replacement
Laminated oak floor section replacement and refastening
Aluminum duct floor repair on refrigerated bodies
Floor screw and rivet pattern refastening
Subfloor support and crossmember repair under a cargo floor
Scuff band and kick plate replacement
Stake bed and flatbed deck surface coating
Rear impact guard replacement and reinforcement
Dock bumper replacement at the rear frame
Step bumper and grab handle replacement
Curbside and side access door repair
Cargo body lighting circuit repair and lamp replacement
Interior dome and strip lighting installation
Clearance and marker lamp housing replacement
Body mount inspection and mounting hardware replacement
Vent and louver panel replacement
Skylight and roof vent resealing
Corner cap and rain gutter replacement
Cargo body panel refinish and blending
Graphics reproduction on replaced skin panels
Unit numbering and lettering reapplication after skin work
Body squareness measurement across the cargo opening
Door opening diagonal measurement and correction
Rear door hold back and cane bolt repair
Loading ramp and ramp slide track repair
Ramp assist spring replacement
Handrail and grab bar reinforcement
Tie down ring and anchor point installation
Cargo net and strap anchor repair
Final door operation, latch and seal verification

WO-05 Trailer and Chassis

6 detailed, 64 additional

Sidewall panel section replacement between uprights
Full height skin sheet replacement on sheet and post trailers
Bonded plate panel patch and edge seal
Upright splice above the damage zone
Logistics post replacement and slot alignment
Top rail straightening and section replacement
Bottom side rail repair and section splice
Rub rail replacement and fastener line renewal
Corner post replacement at the rear frame
Rear frame square up and header repair
Roof bow replacement and re-spacing
Roof sheet seam patch and lap seal
Translucent roof panel replacement
Nose panel and front wall repair
Scuff liner band replacement
Interior lining panel replacement
Rivet line replacement in aluminum skin
Structural blind fastener replacement at post to rail joints
Buck rivet removal and reset
Hardwood laminated oak deck board replacement
Full deck replacement with new fastener pattern
Apitong deck plank replacement on flatbeds
Floor screw pattern renewal and countersink repair
Crossmember replacement in the damaged bay
Crossmember splice and sister repair
Bottom flange crack stop drilling and weld repair
Upper coupler plate inspection and weld repair
Kingpin area gusset repair
Slider box rail weld repair
Landing gear leg replacement
Landing gear gearbox replacement
Cross shaft and connecting tube replacement
Sand shoe and foot pad replacement
Landing gear mounting bracket rebuild
Crank handle and holder replacement
Pintle hook and mounting plate replacement
Lunette ring and drawbar eye replacement
Ball coupler and A-frame repair on utility trailers
Safety chain D-ring replacement and reinforcement
Nose box junction panel replacement
Seven conductor socket and plug replacement
Main harness replacement and reroute through crossmembers
LED clearance and marker lamp conversion
Stop, turn and tail lamp replacement
License plate lamp and bracket replacement
Ground path repair and terminal cleanup
Voltage drop testing on lamp circuits
Horizontal E-track installation
Vertical E-track and logistics track installation
Recessed pan fitting and D-ring installation
Weld on D-ring installation with backing plate
Load bar and decking beam socket installation
Stake pocket and rub rail tie down repair
Winch track repair on flatbeds
Media blast and profile prep on frame sections
Zinc rich primer application on repaired steel
Chassis undercoating and cavity treatment
Dissimilar metal isolation at aluminum to steel joints
Drain hole clearing and edge seal renewal
Seam sealing at roof to sidewall joints
Mud flap bracket and hanger repair
Placard holder and document box installation
Reflective conspicuity tape replacement
Unit number and height decal replacement

WO-06 Equipment and Upfit

9 detailed, 60 additional

Liftgate Install and Repair$1,500 up
Service and Utility Body Install$2,500 up
Toolbox and Crane Body Install$1,500 up
Van Shelving and Racking$750 up
Bulkhead and Partition Install$400 up
Headache Rack and Cab Guard$750 up
Hitch and Coupling Plate Install$500 up
Emergency and Work Lighting Install$400 up
Roof Rack and Ladder Install$400 up

Liftgate platform replacement and resurfacing
Gate frame weld repair at the chassis rail
Cylinder mount rebuild and pin replacement
Power unit box mounting and sealing
Gate power cable run with circuit breaker at the source
Platform retention flipper and ramp replacement
Rear impact guard relocation and reattachment
Cart stop and platform latch installation
Service body mounting to frame rails with U-bolts and spacers
Body sill fabrication and replacement
Mounting bracket and fishplate fabrication
Compartment door gasket and seal replacement
Rotary latch adjustment and replacement
Gas strut replacement on compartment doors
Compartment drain hole clearing and re-establishment
Master compartment shelf and divider fabrication
Underbody box mounting and reinforcement
Crane pedestal subframe fabrication
Crane body outrigger mount reinforcement
Compressor and welder deck mounting
Crossover, chest and side mount toolbox installation
Toolbox backing plate and isolation strip installation
Drawer unit installation and floor reinforcement
Van shelving package installation and anchoring
Shelf tray, divider and door kit installation
Floor anchoring with backing plates and sealed penetrations
Wall anchoring into body ribs and structural members
Composite and aluminum shelving swap for weight reduction
Cargo van floor and wall liner installation
Bulkhead and partition installation
Partition window and sliding door installation
Partition to roof and side wall sealing
Headache rack installation on flatbeds and stake beds
Cab guard fabrication and mounting
Rack mounted light bar and beacon provision
Load bar and rack accessory mounting
Receiver hitch installation, Class III through Class V
Pintle plate installation and reinforcement
Gooseneck ball and under deck rail installation
Coupling plate installation on frame mounted base rails
Coupling plate slide adjustment and stop replacement
Seven conductor socket and connector mounting
Warning light bar installation and switch panel wiring
Corner and surface mount warning module installation
Hideaway warning module installation in lamp housings
Directional traffic advisor installation
Scene and flood light installation
Compartment and step well lighting installation
Fused distribution panel and relay center installation
Low voltage cutoff installation on accessory circuits
Roof rack installation with sealed backing plates
Drop down ladder rack installation
Over cab ladder rack installation on pickups
Conduit and pipe carrier tube mounting
Rear door ladder and grab handle installation
Walk ramp and ramp storage installation
Overall height decal remeasure and replacement
Backup camera and mirror bracket mounting
Step and grab handle installation on bodies
Mud flap and hanger installation on upfitted chassis

WO-07 Glass and Accessories

5 detailed, 60 additional

Commercial Windshield Replacement$450 up
Windshield Chip Repair$90 up
Mirror and Camera Systems$400 up
Step and Running Board Install$400 up
Fender Flare and Mud Flap Install$200 up

Door glass replacement on cab and cargo doors
Vent and quarter glass replacement
Back glass replacement on conventional cabs
Tempered glass fragment removal from door cavities and regulator tracks
Windshield molding and reveal trim replacement
Cowl panel and wiper arm removal for glass access
Pinchweld corrosion cut back, treatment and epoxy priming
Urethane bead correction on previously mis set glass
Glass edge chip inspection and condition documentation
Wiper arm, pivot bushing and blade replacement
Washer nozzle and hose routing repair
Glass perimeter water test and reseal
Wind noise tracing at the glass and door opening perimeter
Sun visor, header trim and A pillar trim replacement
Windshield shade band glass fitment
Rain sensor gel pad transfer and reseat
Forward camera bracket transfer to replacement glass
Static target calibration setup on the shop floor
Pre scan and post scan around glass replacement
Single break resin injection repair
Multiple chip repair on one windshield
Crack progression assessment and repair or replace call
Cab interior glass debris cleanup after a breakage
Window regulator and glass run channel replacement
Cargo door window kit installation
Bulkhead and partition window replacement
Rear door glass with defroster grid handling
Window film removal and reapplication around glass work
Convex mirror head replacement
Eight inch round spot mirror bracket and clamp installation
West coast mirror arm and loop assembly replacement
Mirror glass only replacement, heated and unheated
Power mirror motor and switch replacement
Mirror mount bracket and door skin backing repair
Hood and fender mounted mirror installation on cab forward units
Camera monitor system display mounting in the driver sight line
Reverse camera and harness routing
Side camera pod mounting on box rails and pillars
Camera monitor system arm and pod replacement
Mirror and camera field verification with a walk around spotter
Step tube mounting to rocker pinch seam brackets
Running board bracket replacement
Frame outrigger step bracket fabrication and mounting
Cab entry grab handle installation
Step tread and anti slip insert replacement
Rear bumper step pad replacement
Fold down step, hinge and spring repair
Deck plate and catwalk step panel replacement
Fender flare bracket and rivnut installation
Flare edge trim and gasket replacement
Square tube mud flap hanger installation
Anti sail mud flap bracket installation
Quarter fender installation on tractor units
Poly fender replacement on trailer axle positions
Fender brace straightening and reinforcement
Splash guard installation at van wheel arches
Mud flap graphic and unit number application
Weatherstrip replacement at door and glass openings
Corrosion coating on repaired glass and accessory mounting points
Marker lamp lens replacement within step and flare assemblies

WO-08 Makes We Service

8 detailed, 67 additional

Freightliner Fleet Body Repair$750 up
Peterbilt Fleet Body Repair$750 up
Kenworth Fleet Body Repair$750 up
International Fleet Body Repair$750 up
Volvo and Mack Fleet Body Repair$1,500 up
Isuzu and Hino Fleet Body Repair$750 up
Sprinter, ProMaster and Transit Body Repair$750 up
EV Delivery Van Body Repair$750 up

Aluminum cab skin panel replacement
Steel cab corner sectioning at factory seams
Composite hood crack repair by back face lamination
Fiberglass hood corner rebuild and fairing
Butterfly hood hinge set alignment
One piece tilt hood cylinder and bracket repair
Hood to fender gap setting and reveal correction
Chrome bumper removal, straightening and refit
Steel bumper reinforcement replacement
Bumper energy absorber bracket replacement
Roof fairing and cab extender replacement
Chassis side fairing and skirt repair
Sleeper to cab joint gasket and sealant renewal
Cab mount isolator replacement
Rear cab air suspension bracket crack repair
Cab corner post straightening
Door skin replacement on steel and aluminum cabs
Door shell replacement and hinge alignment
Door glass frame and run channel truing
Cowl panel replacement and plenum drain restoration
Windshield opening flange repair and squaring
Grille and grille surround replacement
Headlamp housing bracket and mount repair
Fender bracket and cantilever mount repair
Poly fender replacement
Quarter fender and bracket installation
Battery box door and step assembly body repair
Deck plate and catwalk panel repair
Frame rail straightening and three dimensional measuring
Cab floor pan section replacement
Cab bulkhead panel repair
Rocker panel and step well sectioning
Unibody pillar sectioning to published procedure
Sliding door track geometry correction
Sliding door roller carrier and bracket replacement
Rear cargo door hinge and check strap replacement
Van roof rib and skin repair
Wheel arch and rocker corrosion cut out and section
Van body side dent and crease repair
Tilt cab hinge and latch repair on cab forward units
Cab step well and grab handle structural repair
Dry freight box headboard replacement
Box rub rail and corner post replacement
Box to frame mounting bracket repair and squaring
Roll up door panel and track section replacement
Translucent roof panel replacement on box bodies
Box floor board and crossmember repair
High voltage shutdown, verification and lockout before body work
Battery enclosure clearance mapping before cutting or welding
Reduced temperature refinish cycle on electric units
Underbody shield reattachment on electric vans
Charge port door alignment and latch repair
Aluminum panel repair in a dedicated isolated work area
Self piercing rivet and structural adhesive seam restoration
Huck fastener removal and replacement on riveted cab panels
Weld through primer application and cavity wax restoration
Seam sealer profile replication to the factory pattern
Anchoring, staged structural pulls and measurement documentation
Forward radar aiming after front structure work
Windshield camera recalibration after cab or glass work
Blind spot radar bracket repair in rear bumper corners
Paint code retrieval from the cab or chassis data plate
Two tone break line layout and reproduction
Pearl and metallic letdown panel spray out
Edge to edge panel refinish and adjacent panel blending
Corrosion coating on repaired seams and fastener penetrations
Unit numbering and reflective marking replacement after refinish

A-Z Alphabetical

Every detailed service, A to Z

Next step

Not sure which line item you need

Send photos and the unit number. We identify the scope, quote the band, and tell you how many days it holds the unit. The drive from Santa Ana is about 17 miles.

Request a Quote (714) 909-1844

All work is performed at our Yorba Linda facility. Estimates are scheduled, not walk up.